Porcelain Slab Slip Resistance: PTV and R Ratings Explained
Slip resistance for porcelain in the UK is specified using a Pendulum Test Value, or PTV, measured under BS 7976 following UK Slip Resistance Group guidance. An R rating, which manufacturers quote far more often, comes from a different test entirely and cannot be converted into a PTV. This page explains the difference, what our slabs carry, and what we recommend where slip resistance matters.
PTV: the measurement UK projects are specified to
A Pendulum Test Value is taken with a pendulum tester on the actual surface. The result is read against established bands:
- 0 to 24 is treated as a high slip potential
- 25 to 35 is a moderate slip potential
- 36 and above is a low slip potential
Because the pendulum measures the surface as it actually is, the result changes with wetness, contamination, the cleaning regime and the installed condition. A figure measured dry in a factory tells you very little about a wet shower floor. Ramps, slopes and level access thresholds require a higher value than a flat floor.
R ratings: a laboratory classification, not a site measurement
An R rating comes from DIN 51130, a German inclined ramp test. A person walks on an oiled surface while the ramp angle increases, and the angle at which grip is lost gives a classification from R9 to R13. It is useful as a broad product classification. It is not a measurement of the floor you are specifying.
Why an R rating cannot be converted into a PTV
There is no reliable conversion between the two. They are different test methods, with different contaminants, different equipment and different conditions. Treating an R rating as though it were a PTV is a common specification error, and it is the reason a surface can satisfy a manufacturer datasheet and still fail on site.
If a project specification calls for a PTV, an R rating does not answer it.
What Infinity Surfaces slabs carry
Infinity classify the matt finish as R9 under DIN 51130. Satin and polished finishes carry no R rating.
We do not hold PTV data for these slabs. A PTV has to be measured independently on the specified finish, which is why manufacturers rarely publish one. We would rather tell you that plainly than quote a number that does not apply to your floor.
Where this matters most
- Wet areas, including shower floors, wet rooms and pool surrounds
- Level access thresholds and entrances where water is carried in
- Public circulation routes and any area covered by a duty of care
- External paving, ramps and any sloped surface
- Commercial kitchens and anywhere grease or contamination is present
What we recommend
Where slip resistance is critical, we recommend independent pendulum testing of the specified finish before it is confirmed. Test the finish you are actually using, in the condition it will be used in.
Talk to us early where flooring is in a wet or public area. We can tell you what we know, what we do not, and what will need testing, which is usually a faster route to a safe specification than working from a datasheet.
Frequently asked questions
What is a PTV?
A Pendulum Test Value is a measurement of slip resistance taken with a pendulum tester under BS 7976, following UK Slip Resistance Group guidance. It is the measurement UK projects are normally specified to. A PTV of 36 or above is treated as a low slip potential.
What is an R rating?
An R rating comes from DIN 51130, a German inclined ramp test carried out in a laboratory with a person walking on an oiled surface. It is a product classification, not a site measurement, and it is widely quoted by manufacturers.
Can an R rating be converted into a PTV?
No. They are different test methods measuring different things under different conditions. There is no reliable conversion between the two, and treating an R rating as though it were a PTV is a common specification error.
Do Infinity Surfaces slabs have a PTV?
We do not hold PTV data for these slabs. A PTV has to be measured on the actual finish by independent testing, which is why manufacturers rarely publish one. Where slip resistance is critical we recommend independent pendulum testing of the specified finish before it is confirmed.
What R rating do Infinity slabs carry?
Infinity classify the matt finish as R9 under DIN 51130. Satin and polished finishes carry no R rating.
Related: technical data and downloads, and the large format porcelain specifier’s guide.